8mm Forum


  
my profile | my password | search | faq | register | forum home
  next oldest topic   next newest topic
» 8mm Forum   » 8mm Forum   » Eumig S807 Sound Head Cleaning

 - UBBFriend: Email this page to someone!    
Author Topic: Eumig S807 Sound Head Cleaning
Martin Dew
Expert Film Handler

Posts: 204
From: Henley-on-Thames, UK
Registered: Jan 2017


 - posted August 21, 2017 06:58 AM      Profile for Martin Dew     Send New Private Message       Edit/Delete Post 
I think I saw a thread somewhere on here recently where someone was explaining how to remove the sound head assembly on the Eumig Mark S807 (or 810) to clean the heads and path.

I've been unable to locate that thread again. Can anyone direct me to that thread, or would anyone be kind enough to list the steps again?

 |  IP: Logged

Andrew Woodcock
Film God

Posts: 7477
From: Manchester Uk
Registered: Aug 2012


 - posted August 21, 2017 07:45 AM      Profile for Andrew Woodcock         Edit/Delete Post 
For the 800 Eumig Seies....

Cleaning the Sound Head:

METHOD 1: (for a quick clean). The sound head is located right underneath the Bulb. It has a white cable coming out of it, which plugs into a receptacle on the chassis. For a real quick clean, take a can of air duster and blast air down into the Teflon film chute at the front of the sound head assembly. This will blow out any loose oxide particles in the sound head. This process is recommended after every couple of reels, to keep oxide from building up inside the head assembly.

METHOD 2: ( FOR A THOROUGH CLEAN, THIS PROCEDURE TAKES ABOUT 30 MINUTES, AND REQUIRES DISSASSEMBLY OF THE SOUND HEAD).
1. Set the control knob to the Forward position then pull off the black control knob at the side of the projector. Remove the lamp housing cover.
2. Pull off the volume control knob and the mixing control knob.
3. Undo the screw located between the volume control knob and the mixing knob, and pull the side panel forward and out to expose the inside of the projector.
4. Unplug the sound head, then undo the single screw which bolts the sound head to the chassis wall.
5. Remove the sound head.
6. Look at the sound head. There are a total of 6 screws in view. Do NOT touch the four innermost screws, they are used for the critical elevation and azimuth alignment of the sound head to the magnetic tracks on the film. Undo the 2 outer screws to remove only the MU-METAL magnetic shield, and the pressure pad assembly. You now have total access to the heads and pressure pads for a thorough cleaning with alcohol. Be very gentle in wiping the head areas. You may wish to de-magnetize the heads while you are at it, using a Radio Shack tape- head demagnetizing probe. Also polish the film channel and pressure pads with Pledge or Favor furniture polish.
7. After cleaning, reassemble the mu-metal shield and pressure pad assembly to the head, and tighten down the 2 outermost screws.
8. Align locating hole on the sound head with the pin in the chassis, and bolt back into place with the single screw. Plug the sound head back into the wall connector.
9. Reassemble the side panel, audio knobs, and Main control knob. Return the control knob to the OFF position

Courtesy of Mr Paul Adsett here, a great admirer of many of the Eumig range of Dual Gauge and Super 8mm projectors.

[Wink]

--------------------
"C'mon Baggy..Get with the beat"

 |  IP: Logged

Steve Klare
Film Guy

Posts: 7016
From: Long Island, NY, USA
Registered: Jun 2003


 - posted August 21, 2017 07:56 AM      Profile for Steve Klare   Email Steve Klare   Send New Private Message       Edit/Delete Post 
This one is among a lot of useful information covered in "Index of Technical Topics" stickied up top.

--------------------
All I ask is a wide screen and a projector to light her by...

 |  IP: Logged

Martin Dew
Expert Film Handler

Posts: 204
From: Henley-on-Thames, UK
Registered: Jan 2017


 - posted August 21, 2017 03:52 PM      Profile for Martin Dew     Send New Private Message       Edit/Delete Post 
Great, many thanks!

 |  IP: Logged



All times are Central  
   Close Topic    Move Topic    Delete Topic    next oldest topic   next newest topic
 - Printer-friendly view of this topic
Hop To:

Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2