8mm Forum


  
my profile | my password | search | faq | register | forum home
  next oldest topic   next newest topic
» 8mm Forum   » 9.5mm Forum   » Pathe Gem

 - UBBFriend: Email this page to someone!    
Author Topic: Pathe Gem
Terry Sills
Phenomenal Film Handler

Posts: 1423
From: Weymouth,Dorset,England
Registered: Oct 2012


 - posted September 05, 2015 03:46 AM      Profile for Terry Sills     Send New Private Message       Edit/Delete Post 
I have a 9.5 Pathe Gem which works ok but the motor "hunts", that is to say the speed varies. Does anyone know what governs the speed and how to adjust/cure this problem so that the speed remains constant?

 |  IP: Logged

Mike Shaw
Junior
Posts: 26
From: Canberra, Australia
Registered: Jan 2015


 - posted September 08, 2015 06:10 PM      Profile for Mike Shaw   Email Mike Shaw   Send New Private Message       Edit/Delete Post 
There's no adjustment for this Terry but if the machine as been laying idle for some time you'll find the original belt as gone hard and is out of shape...so replace....also if motor mounts are weak this can course problem....If belt the problem you will find original belt made out of fan belt material replace with 'O' ring of right size or else will pull motor mounts towards shutter.

 |  IP: Logged

Terry Sills
Phenomenal Film Handler

Posts: 1423
From: Weymouth,Dorset,England
Registered: Oct 2012


 - posted September 09, 2015 02:17 AM      Profile for Terry Sills     Send New Private Message       Edit/Delete Post 
Thanks for that info Mike. I will have a look at that.

 |  IP: Logged

Terry Sills
Phenomenal Film Handler

Posts: 1423
From: Weymouth,Dorset,England
Registered: Oct 2012


 - posted September 14, 2015 01:34 AM      Profile for Terry Sills     Send New Private Message       Edit/Delete Post 
Well it seems the belt is not the problem. The motors acts in the same way even without a belt. It seems to be a motor fault. Are there brushes on the Gem motor?

 |  IP: Logged

Vic Newey
Film Handler

Posts: 41
From: Worcestershire, England
Registered: Dec 2015


 - posted December 27, 2015 08:40 AM      Profile for Vic Newey   Author's Homepage   Email Vic Newey   Send New Private Message       Edit/Delete Post 
Did you find the fault eventually ?, I have a similar problem which I think is related to the speed resistance windings. Speed on mine only worked when the lever was far to the left but the motor kept slowing & speeding up again and I've just unwound mine and found it's broken in several places so presumably it's causing fluctuations in the voltage going to the motor.
I'm now looking for details of the correct wire to get to replace it as it's a simple job that just requires patience to get the windings tightly together.

 |  IP: Logged

Terry Sills
Phenomenal Film Handler

Posts: 1423
From: Weymouth,Dorset,England
Registered: Oct 2012


 - posted December 28, 2015 02:40 AM      Profile for Terry Sills     Send New Private Message       Edit/Delete Post 
Vic
No I didn't investigate further but what you describe sounds very feasible and is most likely the problem with mine. I will have to get round to it sometime soon. I have been very fortunate to obtain another Gem that came with the original box and instructions- very unusual to find in such good condition- and good working order too. I think I have some resistance wire somewhere that might be suitable for the job. Does it have to be exactly the same spec as the original?

 |  IP: Logged

Vic Newey
Film Handler

Posts: 41
From: Worcestershire, England
Registered: Dec 2015


 - posted January 01, 2016 08:54 AM      Profile for Vic Newey   Author's Homepage   Email Vic Newey   Send New Private Message       Edit/Delete Post 
Thanks for the reply Terry,

I would think the wire has to be very similar guage, I carefully rewound mine with some heavier guge wire that I had in the shed & although it runs o.k the speed won't alter & stays constant, I've ordered a spool of resistance wire off Ebay, I found a mention of the correct guage on this forum & the wire on order is about right so I will post an update when it arrives.

 |  IP: Logged



All times are Central  
   Close Topic    Move Topic    Delete Topic    next oldest topic   next newest topic
 - Printer-friendly view of this topic
Hop To:

Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2