This is topic Sankyo 2000h belt in forum 8mm Forum at 8mm Forum.


To visit this topic, use this URL:
https://8mmforum.film-tech.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=1;t=010487

Posted by James Wilson (Member # 4620) on February 05, 2016, 12:14 PM:
 
Hi
Ive just been doing some work, end of reel one belt breaks, no big deal so I thought, after all I`ve changed it many times before.

Well it was a bit of a pig to change first I could`nt find my long nose pliers, which I find it impossible to change without.
Has anybody noticed what a short life time these belts have, If I remember correctly they used to go on & on.

Oh! I finished the job on my spare 2000h.

Kind Regards,
James.
 
Posted by Barry Fritz (Member # 1865) on February 05, 2016, 01:07 PM:
 
I don't run my Sankyo much so I have not had a belt breakage problem with it. Where do you get your replacement belts from?
 
Posted by Janice Glesser (Member # 2758) on February 05, 2016, 01:33 PM:
 
James...are you removing the lamp and the screws to detach the shield plate as shown in this picture to change the belt?

 -

... and then following the process in this video to take off the old belt and put on the new belt?

http://www.youtube.com/watch?v=rog95Djbtpc&list=UUzhVuBJou11ziWdERi0ZGuQ&index=15

You should not need pliers. Perhaps the pliers are cutting into the belt material and weakening it. The belts on my Sankyos have only been replaced once and seem to last for years.

[ October 17, 2017, 08:47 AM: Message edited by: Janice Glesser ]
 
Posted by James Wilson (Member # 4620) on February 06, 2016, 04:38 AM:
 
Hi Barry,

I get my belts from ebay UK, here`s the link
http://stores.ebay.co.uk/e-s-photographics?_trksid=p2047675.l2563
hope this of use,

Hi Janice,
That`s exactly the same way as I do it apart from pulling the belt through the light housing with the long nose pliers
(very gently) to slip onto wheel, I can`t get my fingers in their as I can on the 1000 model.

All the best, James.

[ February 06, 2016, 05:52 AM: Message edited by: James Wilson ]
 
Posted by Barry Fritz (Member # 1865) on February 06, 2016, 11:51 AM:
 
Hi James:
I was just wondering if the quality of the belts was an issue. Seems as though your source should be reputable.
 
Posted by James Wilson (Member # 4620) on February 06, 2016, 12:10 PM:
 
Hi Barry,

It`s me, I think seeing as the 2000h is on just about every day for six hours or so, they probably do very well.
Regards,
James.
 
Posted by Ty Reynolds (Member # 5117) on February 06, 2016, 01:21 PM:
 
James - I use a hook made from coat hanger wire to pull the belt through the opening and over the pulley.
 
Posted by Pasquale DAlessio (Member # 2052) on February 06, 2016, 02:54 PM:
 
Maybe you damaged the belt with the needle nose pliers? or the path where the belt runs? Just a thought [Confused]
 
Posted by Rich Malmsten (Member # 5787) on February 08, 2017, 09:43 PM:
 
I just want to say that this thread was exactly what I needed to get my Sankyo 2000H back up and running. A couple of weeks ago I was watching some of my grandfather's 8mm home movies that he shot in the 1940s, and the take-up reel stalled while I was playing a 400-ft reel. I took off the back cover to find that the main drive belt seemed stretched.

The thread suggested where to buy a replacement belt (E.S. Photographics in the U.K.). I ordered one and it came in about two weeks with no problems.

Janice's detailed instructions on removing the lamp plate made replacing the belt a snap. The whole operation took less than 10 minutes from start to finish. It was almost too easy! The only detail I would add is that the two screws for the lamp plate are not interchangeable; they're different sizes, so be sure to put the smaller one in the lower hole. Figuring out that minor detail took me longer than putting on the belt itself.

So now the Sankyo is as good as new and ready to show more old home movies.

BTW - I'm new to this forum. I've been collecting film, both Super-8 and 16mm, for about 15 years, but registered just last week.

Best wishes!
Rich
 
Posted by Janice Glesser (Member # 2758) on February 08, 2017, 11:54 PM:
 
Welcome Rich and thank you for adding more detail to this thread.
 


Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2