This is topic Super 8 Home Movie Film on Polyester? in forum 8mm Forum at 8mm Forum.


To visit this topic, use this URL:
https://8mmforum.film-tech.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=1;t=011941

Posted by Will Trenfield (Member # 5321) on December 10, 2017, 04:58 PM:
 
Sorry if this is a naff question. I recently acquired a home movie on a 3" reel. The plain leader seemed to be attached with film cement but, when I tried to cement a tail to the end, it wouldn't work. There's no manufacturer's name anywhere on the film or spool and the edges of the film are black. This holiday movie seems to have been shot in Florida. Was polyester based home movie film available in the USA? If so, what film cement was used?
 
Posted by Nantawat Kittiwarakul (Member # 6050) on December 11, 2017, 04:04 AM:
 
Fuji Single8 film?
It's dimensionally identical to usual Super8,but the base is probably poly. Another telltale would be that if you shine the light through it,poly will be more "transparent" compared to ordinary celluloid. Hope this helps. [Smile]
 
Posted by Brian Fretwell (Member # 4302) on December 11, 2017, 05:39 AM:
 
The lab may have used a type of welder (ultrasonic?) to attach the leader as I believe that was possible or superglue, which I read somewhere was developed to splice polyester film. In the UK Dixons Prinzcolor film could be polyester, I don't know who manufactured it.

The only Fuji Single 8 spool of home movie film I have seen was on a smaller than 3inch reel.
 
Posted by Will Trenfield (Member # 5321) on December 11, 2017, 12:29 PM:
 
Thanks for the replies. It sounds like it could be Fuji film. The leader is fractionally wider than the film. I didn't know about the use of superglue. You learn something all the time on this forum.
 
Posted by Maurice Leakey (Member # 916) on December 12, 2017, 11:25 AM:
 
Fuji single 8 stock was polyester based with a possible maximum length of 40ft.
A 3" spool would normally accommodate 50ft of Kodak, or similar, stock.
Dixons Prinz Color was made in Italy by Ferrania and had a cellulose acetate base.
 
Posted by Will Trenfield (Member # 5321) on December 19, 2017, 06:02 PM:
 
Brian mentioned the use of super glue to join polyester film. I had a film breakage tonight at the start of a commercial release on polyester so I thought I'd try it out. I used my cement splicer but carefully applied a small drop of Locktite Super Glue as you'd do with a acetate cement splice. No problem! It made a good strong joint in seconds. Best to wear gloves though.
 
Posted by Phil Murat (Member # 5148) on December 20, 2017, 04:15 AM:
 
Hi Will,

Very interesting solution described here.

I have been thinking about the way to perform polyester splices using Cyanolit glue. To do that , I am thinking about the way to modify a former classical splicer (for Acetate Films) by adding a PTFE tape on guides to prevent from unwanted film sticking on splicer parts due to little glue overflow.

Of course just a very small drop of glue is necessary.

Cyanolit Glue is 100% compatible with Polyester material.

To follow......

That could be an interesting Topic to add in the list I assume.
 
Posted by Maurice Leakey (Member # 916) on December 20, 2017, 04:40 AM:
 
It does seem rather dangerous to use super glue. It will stick most things to most things, such as fingers. [Smile]
Perhaps better to use tape.
 
Posted by Alexander Vandeputte (Member # 1803) on December 20, 2017, 11:13 AM:
 
Please use tape, as tiny glue particles can (will ?) get stuck in the gate and can (will?) cause scratches and lines...
 
Posted by Will Trenfield (Member # 5321) on December 20, 2017, 05:59 PM:
 
I wasn't advocating the use of super glue, only reporting that it will bond polyester film. I wore cotton gloves and only used a tiny drop on the film. Obviously, if too much were to be used, it could overflow onto the splicer as Phil's post indicates. What's needed is a safer glue that will bond polyester in seconds but not adhere to metal well.
 
Posted by Phil Murat (Member # 5148) on December 22, 2017, 10:24 AM:
 
Hi Will,

Cyanoacrilate glue is fluid such as water and sticks almost instantly and almost every material apart polyethilen , PTFE.....

Under special cares this is a great material to use.

I'll make test(s) with a former (modified) motorized Hahnel splicer and a magnifying glass.

Merry Christmas and Best Wishes

Phil
 
Posted by Will Trenfield (Member # 5321) on December 22, 2017, 04:12 PM:
 
I see. The use of PTFE tape would prevent the film sticking to the splicer if too much super glue were to be used. I wonder, though, what adhesive is used for splicing tape which would be safer to use. Does anybody know? Compliments de la saison et un bon 2018!
 


Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2