8mm Forum: Bolex 18-5L Super - No voltage to bulb.

»	8mm Forum » 8mm Forum » Bolex 18-5L Super - No voltage to bulb.

UBBFriend: Email this page to someone!

Author

Topic: Bolex 18-5L Super - No voltage to bulb.

Andrew Scales
Junior
Posts: 5
From: Tennessee
Registered: Jan 2011

posted January 08, 2011 06:29 PM

I am relatively new to the hobby and new here, so I guess I will jump right in!

I was able to get a 18-5L for free from a retiring teacher who left it behind. I thought that leaving it was silly and there was no reason for it. But after a little investigating I found that the lamp would not turn on. Every thing else on this projector works in more or less decently. So to investigate the problem I inspected the halogen lamp only to find it trouble free. I looked at the connectors and they looked okay. Then I tested the voltage, and there wasn't a completed circuit. I assume that the issue is somewhere in the wire that goes into the box with the controls in it and there is something that has come disconnected. So I decided to come here for help to get this garbage can find back on its feet. I hope that someone here could guide me with the wiring to get it re-connected or fixed. I will post pictures if there is a need but I assume that those who can help already know something about this model of projector.

Thanks in advanced,
Andrew-

[ July 26, 2012, 06:08 PM: Message edited by: Andrew Scales ]

| IP: Logged

Andrew Scales
Junior
Posts: 5
From: Tennessee
Registered: Jan 2011

posted January 09, 2011 10:55 AM

I have exhausted most of my hope for this...

| IP: Logged

Barry Fritz
Phenomenal Film Handler

Posts: 1061
From: Burnsville, MN, USA
Registered: Dec 2009

posted January 09, 2011 12:40 PM

To clarify, you used a voltmeter and touched the two connetors that are on the red wires that run to the lamp bracket, and did not get a reading? Was the control knob turned to 18 or 5 when you did this? If that is not what you did, try that. You should get a reading of 12 or therabouts. I have two that work and that is what they read. I've got one that does not work and it reads 13.5.

| IP: Logged

Andrew Scales
Junior
Posts: 5
From: Tennessee
Registered: Jan 2011

posted January 09, 2011 02:35 PM

Yes, that is exactly what I did.

I tried it again and I am getting 0-.5v now, so I know there is power, but it is getting eaten some were and there is some resistance in the circuit too, about a half an ohm.

| IP: Logged

Barry Fritz
Phenomenal Film Handler

Posts: 1061
From: Burnsville, MN, USA
Registered: Dec 2009

posted January 09, 2011 07:32 PM

I wish I knew what the problem is you are having, but I am not an electrical guy otherwise I may be able to fix mine also. If you open the back, there is a rectangular black metal cover that covers a terminal where wires attach. I'm not certain what that is, but may be a voltage regulator. You might check there and see if anything appears out of order. Run some voltage checks at the terminals. I hope you solve the problem as you have a very nice projector and the price was right.

| IP: Logged

Andrew Scales
Junior
Posts: 5
From: Tennessee
Registered: Jan 2011

posted January 09, 2011 09:22 PM

Checked the transformer, and I found my 12v in there! [Smile]

So I am assuming it is somthing in the switch assembly that is acting up, I took that off but I cant seem to get it out all the way because the wires are holding on to it. Is there any way to get that all the way off so I can check the electronics inside?

EDIT
Used jumpers to test the bulb etc. It is for sure the right terminals. I may just add jumpers to get it working until I can get the switch fixed up all the way (if I can)

Thanks

[ January 10, 2011, 11:33 AM: Message edited by: Andrew Scales ]

| IP: Logged

Barry Fritz
Phenomenal Film Handler

Posts: 1061
From: Burnsville, MN, USA
Registered: Dec 2009

posted January 10, 2011 11:50 AM

I know what you mean about the switch assembly. Comes up a very short way before wires stop it. I suppose you could direct connect, but then the lamp would be on all the time unless you unplug it.

| IP: Logged

Andrew Scales
Junior
Posts: 5
From: Tennessee
Registered: Jan 2011

posted January 10, 2011 08:49 PM

I am going for the direct connect. The good thing is that it doesn't just stay on, it goes off when in the off/stop position. The downside is it does come on in the "M" mode.

After all it is a working Bolex projector I got for free! so there is a huge plus!

| IP: Logged

Barry Fritz
Phenomenal Film Handler

Posts: 1061
From: Burnsville, MN, USA
Registered: Dec 2009

posted January 11, 2011 08:52 AM

Well, it seems like you have come up with a workable solution. I don't think it is a major problem that it is on in the "M" position. That is for autoloading and the film is moving through fast enough that it shouldn't burn.

| IP: Logged

All times are Central

Printer-friendly view of this topic

UBB.classic^TM 6.3.1.2