8mm Forum


  
my profile | my password | search | faq | register | forum home
  next oldest topic   next newest topic
» 8mm Forum   » 8mm Forum   » Elmo ST-1200D 24V 250W conversion problem

 - UBBFriend: Email this page to someone!    
Author Topic: Elmo ST-1200D 24V 250W conversion problem
Christian Schatz
Film Handler

Posts: 57
From: Germany
Registered: Feb 2012


 - posted December 21, 2013 05:49 PM      Profile for Christian Schatz   Email Christian Schatz   Send New Private Message       Edit/Delete Post 
Hello,

today i've done the 24V 250W conversion on a Elmo ST-1200D. Using
an external transformer and a 24V/250W ELC for 16mm projectors.

I can't see a difference between 15V 150W and 24V 250W. I found a forum where someone stated that the ELC
bulb must replaced 10mm back in the lamphouse on an GS. So i tried that on my ST. Can't see any difference in lightoutput on my 2m x 2m screen ...

Am i doing something wrong or is the difference so small that i can't see it? [Roll Eyes]

Kind regards,
Chris

--------------------
KINOTON FP30D w/ 1kW Xenon & FP30 w/ 1.6kW Xenon
BAUER SONOLUX II w/ 36V/400W Halogen
CARL ZEISS TK35/52 w/ 36V/400W Halogen
ELMO ST-1200D M&O 24V/250W Mod with Schneider Lens 1.1 / 11-25

 |  IP: Logged

Graham Ritchie
Film God

Posts: 4001
From: New Zealand
Registered: Feb 2006


 - posted December 21, 2013 06:03 PM      Profile for Graham Ritchie   Email Graham Ritchie   Send New Private Message       Edit/Delete Post 
I don't think you are doing anything wrong, even my 100watt on a ST180 projector looked brighter than the dim 200watt EJL on the GS1200. So I am not sure that its all down to wattage for a brighter picture.

However in saying that, is the lamp getting the full 24 volts?
Another thing I would recommend is using the Osram Xenophot 24volt/250watt ELC lamp.

Graham

 |  IP: Logged

Christian Schatz
Film Handler

Posts: 57
From: Germany
Registered: Feb 2012


 - posted December 21, 2013 06:13 PM      Profile for Christian Schatz   Email Christian Schatz   Send New Private Message       Edit/Delete Post 
It's getting the full 24V and it's a Osram 64653 HLX ELC 24V/250W Xenophot. The datasheet says the bulb has a working distance of 35mm, so i think i've set the distance from bulb to gate correct.

--------------------
KINOTON FP30D w/ 1kW Xenon & FP30 w/ 1.6kW Xenon
BAUER SONOLUX II w/ 36V/400W Halogen
CARL ZEISS TK35/52 w/ 36V/400W Halogen
ELMO ST-1200D M&O 24V/250W Mod with Schneider Lens 1.1 / 11-25

 |  IP: Logged

Graham Ritchie
Film God

Posts: 4001
From: New Zealand
Registered: Feb 2006


 - posted December 21, 2013 06:55 PM      Profile for Graham Ritchie   Email Graham Ritchie   Send New Private Message       Edit/Delete Post 
It might be as you said, at that screen size its not showing you the difference. I would zoom it out to say eg eight foot and try a comparison between the 150watt against the 250watt once again...it might be worth a try.

I do use the 250watt Osram Xenophot myself in my GS1200 and its certainly a much brighter and whiter lamp.

Graham.

 |  IP: Logged

Christian Schatz
Film Handler

Posts: 57
From: Germany
Registered: Feb 2012


 - posted December 21, 2013 07:10 PM      Profile for Christian Schatz   Email Christian Schatz   Send New Private Message       Edit/Delete Post 
Mhhh ... at 24V there is no difference compared to 150W in my eyes. But if i use 25-27V the picture is MUCH brighter than before. The transformer should give me 300W at 24V. Maybe it gives lesser?

--------------------
KINOTON FP30D w/ 1kW Xenon & FP30 w/ 1.6kW Xenon
BAUER SONOLUX II w/ 36V/400W Halogen
CARL ZEISS TK35/52 w/ 36V/400W Halogen
ELMO ST-1200D M&O 24V/250W Mod with Schneider Lens 1.1 / 11-25

 |  IP: Logged



All times are Central  
   Close Topic    Move Topic    Delete Topic    next oldest topic   next newest topic
 - Printer-friendly view of this topic
Hop To:

Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2