|
Author
|
Topic: WARNING against buying from Iceco/Magnatech
|
David C. Lucidi
Expert Film Handler
Posts: 127
From: Glenolden, PA, USA
Registered: Nov 2013
|
posted June 23, 2015 05:34 AM
Hey all,
I posted this on the other forums, as I am hoping my 'getting the word out' prevents someone from going through what I went through.
This is a long post with lots of references, in hopes of saving someone from making the same money-making mistake I did. Let this serve as a huge warning against buying from ICECO/Magnatech for their 'NOS Projectors' (specifically, the B&H 2585/AML military projectors on Ebay).
Last June my wife/inlaws treated me to a surprise anniversary & Father's Day gift of (2) of the above mentioned projectors. I had minor issues when I first received them (socket issues), which I posted on the 16mm forum. Weeks later as I used them, I had much bigger issues, which if you are a member of the 16mm forum, can be viewed here:
http://16mmfilmtalk.com/viewtopic.php?t=30739&highlight=iceco
If you are not a member of that forum, the short version is that the film would be "jittery and bouncy" after threading (and sounded like it was chewing the film) and was unwatchable. Here's a youtube video showing one of the projectors problems:
https://www.youtube.com/watch?v=15kxBvw2fFI&list=UUbOCSD8zrJjSz_0I_YkO3TQ
Upon Iceco receiving the projectors (less than 7 weeks after I got them, and still under warranty, AND shipped back at MY expense) they claimed they found nothing wrong and blamed it on the film I was using (I tested with 4 different types of film; ALL had the exact same problem). I wrote back that the projectors ARE in fact, problematic; that the 16mm forum alone has MULTIPLE people who have had issues; that the 16mm forum has rebuilders like Richard Burgess claiming he has had to repair multiple projectors that Iceco 'fixed'. I said they BETTER check again and fix it. I didn't want them sent back to me still plagued with problems, needing me to ship it AGAIN at my expense. Well, they 'claimed' to fix the problem, showing me a video from them and the projectors running ok (it should be known that the projectors would *sometimes* run ok on their own (maybe 1 out of 10 times). I got the projectors back...and problems were still there. I was disgusted at this point and wasn't wasting more money to with shipping sending it to them again, esp. since they already claimed 'nothing was wrong'. They absolutely would NOT pay to have it shipped to them (trust me, been there done that). They were VERY difficult to get responses from when I sent them back the first time, either by phone or email.
After pouring through the 16mm forum archives and seeing others who had identical problems, I also saw some comments from repair professionals who had stated things like:
"Sounds like the timing is not correct. ICECO is hit or miss when it comes to this, it is a very precise adjustment and even being off a little can cause this to happen".
"The rebuilding of a B&H 2585 takes a highly skilled expert to adjust properly, followed by some intense testing with different types of film. The specifications are critical. I doubt that Iceco go to these lengths. I have heard other stories of misaligned 2585's. Collectors have sent me some of these rebuilds for further adjustment".
" One of the issues with these New Rebuilt 2585's is that they have been completely taken apart and realigned with a new worm gear. These are extremely critical timing adjustments. I think the person who did yours didn't get it right."
After talking to one of the rebuilders privately, he offered me a price to repair them and have them set to "better than factory specs". At the time, funds were short so I waited. I finally got around to it this month -- Richard has recently repaired the projectors and had sent me a list of all the things wrong with both projectors. This is what he found:
-Claw protrusion out of specification.
-Sprocket timing off, causing incorrect loops, loss of loop.
-Loop restorer would not work, continuous tripping.
-Sound stabilizers way out of adjustment, virtually no tension.
-Speaker polarity off on one projector even though it is color coded.
-One projector had a mis-installed loop restorer cam. It was a hair loose and worked itself out of position.
This is a disgrace! To have this many things wrong, both after a rebuild (before selling) AND after it was sent back to them again? Unacceptable. And while some may say this was an isolated case, it wasn't. The 16mm forum has multiple cases of others who had issues with these projectors AND the exact same problems!
Point is, ICECO/Magnatech have a HISTORY of their 'repaired' projectors NOT being repaired correctly at all. I am out quite a bit of money in shipping to 2 different places (Iceco, and then the rebuilder as well, Richard Burgess), and the additional cost to have it fixed 'right'. My gripe isn't with Richard (quite the opposite, I am delighted it is now 'correct'). My issue is with Iceco selling a poorly rebuilt projector, and then doing a piss-poor repair after it was sent back to them, AGAIN (and initially claiming 'nothing was wrong, it must be your film').
I tried to contact ICECO about this whole matter via email last week, since there was too much to reference on the phone (original Ebay auction #, past repairs, etc.). I sent a detailed email to them last Wednesday morning, asking for their thoughts on the matter before I posted here. Still no response after almost 1 week. Suffice to say, I am done with them, lesson learned the hard way.
Bottom line: Buyer Beware! Think VERY carefully before buying projectors from Iceco. The warranty is USELESS, their rebuilds are a disgrace. Be prepared to have it serviced by someone OTHER than Iceco, if you do buy one of these projectors. I do want to publicly thank Richard Burgess for making this right. I only wish I went to him first as it would have saved me shipping (and headaches) to Iceco for 'warranty repairs' which were far from done correctly.
Thoughts and comments are always welcome.
| IP: Logged
|
|
|
|
David C. Lucidi
Expert Film Handler
Posts: 127
From: Glenolden, PA, USA
Registered: Nov 2013
|
posted June 23, 2015 11:35 AM
Hi Maurice,
Yes, that's the one ![[Mad]](mad.gif)
I goofed above when I said anniversary/Father's Day gift...I meant 40th bday/Father's Day Gift (same difference, but still wanted to set the record straight). The wife and inlaws wanted to get my current 2592 projectors rebuilt for the gift, but also wanted it to be a surprise -- problem was I'd know if they went missing. So they thought they were doing the right thing buying these new.
It was bittersweet when they surpised me, as I already read horror stories on the forums about people who bought from Iceco. But I didn't want to say anything at the time and spoil the surprise or hurt their feelings. I just hoped I'd be lucky and the projectors would be fine. Far from it
What a nightmare to say the least....hopefully my hell will prevent someone else from going through the same thing. If someone does buy it, better factor in the additional cost of shipping it to a competent rebuilder, and THEIR labor costs, as well. ![[Frown]](frown.gif)
| IP: Logged
|
|
|
|
David C. Lucidi
Expert Film Handler
Posts: 127
From: Glenolden, PA, USA
Registered: Nov 2013
|
posted June 26, 2015 01:25 PM
Maurice, they make it sound like it's the best thing since sliced bread. That's why my family bought them. Yes, it's a HELL of a lot of money to spend on (2) projectors, but they felt (as others would, I'm sure), that:
A.) The projectors are new, so they'll last a LONG time.
B.) The dreaded wormgear is replaced, no worries there.
C.) Comes with a 1 year warranty
Like I said, my wife & inlaws wanted to get my current B&H's repaired (cracked wormgears) but they also wanted to be a surprise. Buying these solved both and they figured "Hey, it's NEW and comes with a warranty...how awesome is that?". So they got suckered in.
Points A&B are spot on, Point C is worthless. I have posted this in other forums and now more people are also commenting on having had problems, only to have Iceco claim that "nothing is wrong with it" when they took them back for warranty work (wasting money in shipping). Same line they gave me, even with video proof to the contrary.
Don't get me wrong -- the projectors are AWESOME -- esp. since they have a very rare B&H option: 2 bladed shutter. But the added cost I had to spend to get them 'truly right' really makes the $550 (each!) price sting that much more. Esp. considering these were 'supposed' to be perfectly tuned already.
| IP: Logged
|
|
|
|
|
|
|
|
|
UBBFriend: Email this page to someone!
Printer-friendly view of this topic
