This is topic Speed adjust Eumig S 810 D Lux in forum 8mm Forum at 8mm Forum.


To visit this topic, use this URL:
https://8mmforum.film-tech.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=1;t=011451

Posted by Clinton Hunt (Member # 2072) on April 27, 2017, 08:12 PM:
 
Hi,
Does the Eumig S 810 D Lux sound projector for all 8mm gauges have a way of adjusting the speed?
I just got it yesterday and it hardly moved so I gave the cogs etc a grease and now its going almost as it should.
I think it is running a bit slow.
I've looked in the back and found what looks like a speed pot,there's only one though.
Any advice?
Cheers,Clinton [Smile]
 
Posted by Janice Glesser (Member # 2758) on April 27, 2017, 09:07 PM:
 
Clinton...You can adjust the speed with the front 18 - 24 switch by placing the switch at a position somewhere in between the 18 - 24. If it's not running at 24fps perhaps the motor needs some oiling. I know those pots you are referring to... but I don't recall anyone mentioning there was a way to internally adjust the speed. Hopefully some other Eumig experts can chime in here [Smile]
 
Posted by Clinton Hunt (Member # 2072) on April 27, 2017, 09:37 PM:
 
Thanks for the reply Janice,I had to grease the cogs etc to start with as it hardly moved in forward and slowed to a stop in reverse,that got it running as it should apart from the speed.Let's see what other thoughts are given and hopefully I can get it going right.It is Standard and Super sound which will give me a backup projector if my Elmo dies!
 
Posted by Dominique De Bast (Member # 3798) on April 27, 2017, 11:00 PM:
 
The manual says : "Important : Before changing the running speed, always turn the main switch to stop and connect the projector to the main supply. After switching from 24 to 18 fps, wait for a couple of minutes before projection to slow the flywheel speed to stabilise." Will probably not solve your problem but good to remind.
 
Posted by Maurice Leakey (Member # 916) on April 28, 2017, 02:35 AM:
 
As these models get older and older it is important to give the motor a good run in the non-operating position to get it well warmed up before lacing a film.
 
Posted by Clinton Hunt (Member # 2072) on April 28, 2017, 03:02 AM:
 
Good advice from you guys as always,I will plug it in tomorrow and let it run for an hour or 2 and see what that does [Smile] [Smile]
 
Posted by Maurizio Di Cintio (Member # 144) on April 28, 2017, 07:37 AM:
 
Hello, Clinton. Please tell me: in NZ do you have 50 or 60 Hz mains? And where did your Eumig come from?

In the meantime, it is advisable not to lubricate ANYTHING at all more than you have rightly done yet: the motor does not need anything like that if it runs very siklently while in stand-by mode. Instead you should check that the pulley on top of the motor's shaft is clean and not slippery. Also the rubber covered discs might be hardened and/or somewhat dirty or greasy; in either cases this will cause the pulley to slip to a certain degree when transferring power to the mechanism hence (one) of the possible reasons for your Eumig to run a bit slow. And no, to the best of my knowledge there is no electronic regulation (trim pot etcc) to fine tune its speed: it's a totally mechanic contraption relying on manufacturing precision: both the discs and the pulley are slightly wedge-shaped and this lets the projector achieve the speed change. So both discs and pulley must be clean. If not use a cotton swab with some isopropyl alcohol. If the rubber is hardened, use the finest sand paper and rejuvenate their surfaces just a little so proper contact and grip between pulley and discs is restored. Also check the mains frequency: if the machines is set to work at 60Hz but you have 50 in your area, the projector wil lnoticeably run slower than due.
 
Posted by Andrew Woodcock (Member # 3260) on April 28, 2017, 09:44 AM:
 
Speed potentiometer's are only ever necessary to trim the speed on D.C. motors not A.C. ones like are fitted to this machine.
As Maurizio points out, speed is mechanically governed on this type of machine, not electronically.
Maurizio, as always, offers some good advice here.
 
Posted by Maurice Leakey (Member # 916) on April 28, 2017, 10:13 AM:
 
The electricity supply in New Zealand is 230volts @ 50Hz.
 
Posted by Terry Sills (Member # 3309) on April 28, 2017, 11:01 AM:
 
Mauricio is correct. Do not lubricate anything. There is no speed adjustment other than the 18/24 fps switch. The problem is the contact between the spinning disc on the motor shaft, which is critical. The circular plate that the spinning disc makes contact with is usually rubber coated, although I have seen older models that are plain aluminium. The spinning disc has an outer rubber ring which makes contact with the circular drive plate when the projector is switched to forward or reverse. This simply rocks the motor from a central neutral position to the drive position which brings the spinning disc into contact. The rubber on the spinning disc can be the problem, because unless it makes contact at the correct pressure, the speed of the projector will be slow. Try cleaning both the circular drive plate and the rubber on the spinning disc, this sometimes works. If not take a look at the motor mountings. They are prone to breaking up, in which case you may have to replace them with home made resin or rubber alternatives. Again these motor mounts will affect the critical contact of the spinning disc. It may sound daunting but I have undertaken it successfully.
 
Posted by Janice Glesser (Member # 2758) on April 28, 2017, 12:23 PM:
 
Good to know about the motor guys. I'm making a note of this [Smile] When I've had issues with my Elmo's... the advice has always been to drop some oil on the bushings. I guess that's not the tactic with the Eumig. I also have this same model Eumig and did all the things you have suggested when I first got the projector. My machine is still running fine, so hopefully these steps will improve the performance of Clinton's projector also.
 
Posted by Will Trenfield (Member # 5321) on April 28, 2017, 04:02 PM:
 
The motor mounts that Terry mentioned can be purchased here
http://shop.van-eck.net/film-projector-parts/parts/p-2a/PP-0138.html
 
Posted by Will Trenfield (Member # 5321) on April 28, 2017, 04:02 PM:
 
Rather than sanding the rubber disks, try using ordinary brake fluid (glycol-ether not mineral) left overnight. This causes the rubber to expand.
 
Posted by Tom Photiou (Member # 130) on April 28, 2017, 04:08 PM:
 
can anyone on here give us a play by play how to remove and replace the motor mounts?
 
Posted by Clinton Hunt (Member # 2072) on April 28, 2017, 06:08 PM:
 
Here is a picture of the screw behind the 18 - 24 lever (centre of pic).
I noticed mine didn't go all the way to the top so I undid the screw and moved the back plate slightly,and it worked.
Thanks to this wonderful forum as always!
 -
 
Posted by Janice Glesser (Member # 2758) on April 28, 2017, 07:10 PM:
 
That's terrific Clinton! Happy it was that simple [Smile]
 
Posted by Will Trenfield (Member # 5321) on April 28, 2017, 07:11 PM:
 
In response to Tom's post, I removed the motor on a scrap Eumig Mark 8 a while back pretty easily. There was a small spring on the reverse which came off and I couldn't make out where it fitted. Replacing the motor mounts looked to be straightforward but it could be a pig to put it back together. Glad you sorted your speed problem, Clinton. The lever operates a collar, from what I remember, which raises the motor drive to a different area of the disk drive to increase the speed. I guess that the rubber disk had worn at the original setting.
 
Posted by Clinton Hunt (Member # 2072) on April 28, 2017, 09:17 PM:
 
Here's 2 Youtube videos of my projector in action,Super 8mm sound and Standard 8mm sound [Smile]

https://www.youtube.com/watch?v=Bp_LTDX4mzk

https://www.youtube.com/watch?v=18SFWUUCdu0
 
Posted by Maurice Leakey (Member # 916) on April 29, 2017, 02:21 AM:
 
Great.
I've never seen a Eumig 810 with yellow/beige handle and other parts.
 
Posted by Dominique De Bast (Member # 3798) on April 29, 2017, 03:02 AM:
 
Well done, Clinton !
 
Posted by Clinton Hunt (Member # 2072) on April 29, 2017, 04:37 AM:
 
Thanks Dom,if it had been an electronic problem then I would've been stuck [Smile]
 
Posted by Paul Browning (Member # 2715) on April 29, 2017, 05:26 AM:
 
Hi Clinton, have a look at this youtube video it may help you and other eumig owners with this problem on the drive discs. https://www.youtube.com/watch?v=hqyZqPN-UTo
 
Posted by Tom Photiou (Member # 130) on April 29, 2017, 06:16 AM:
 
Maurice, i think you'll find thats what the years do to the white coating,(a bit like very early plastic windows, they go a wee bit yellowy) [Big Grin]
 
Posted by Clinton Hunt (Member # 2072) on April 29, 2017, 07:15 AM:
 
Hi Paul, that is a great YouTube video,my problem fixed now,I let the projector run for a few hours and everything seems good now.
I liked the way it actually showed the pads etc people talked about!
 
Posted by David Roberts (Member # 197) on April 29, 2017, 07:35 AM:
 
Tom,
years ago I replaced the motor mounts on a mk s using the parts supplied by John White.
it was quite easy except for the fine adjustment,ie exact position of motor in relation to its mounting.
I never got my mk s to run properly in reverse but managed to get it going ok for normal forward projection.
 
Posted by Terry Sills (Member # 3309) on April 29, 2017, 09:35 AM:
 
Well spotted Clinton. Glad it was that easy to fix. Hopefully the motor mounts are still ok but good to know that new spares are available.
Tom - it's fairly easy to remove the motor by undoing the screws that secure the aluminium plate that contains the motor mount, then undoing the two screw either side of the semi circular aluminium casting that the motor sits on. When this casting is removed you can pull the motor towards you so that the rear shaft of the motor slides out of the rear mount. After that you should be able to take the motor out. You may have to take off a black metal plate that sits over the red record button. The power lead spade connector needs to be disconnected and the earth lead is disconnected when you undo one of the screws of the semi circular casting. The fiddly bit is relocating the motor after replacing the motor mounts because you can't see the rear motor shaft or motor mount and it makes it awkward to locate the shaft into the bearing. But it's doable
 
Posted by Tom Photiou (Member # 130) on April 30, 2017, 07:03 AM:
 
Thanks Terry & Dave,
Clinton, Glad to see yours is all up and running fine again [Wink]
 
Posted by Gary Crawford (Member # 67) on May 02, 2017, 07:31 AM:
 
The neat thing about the Eumigs is that the mechanical speed control can be set to any speed BETWEEN 18 and 24fps. You can move that lever anywhere in the middle. This is particularly good for finding a correct speed for various silent era films.
 
Posted by Tom Photiou (Member # 130) on May 02, 2017, 01:03 PM:
 
Following on from this , by undoing that screw Clinton, doesnt the spinning part now go all the way to the top making it run too fast? I tried this and its way to fast, now i cant seem to re adjust it back don. DOHH [Confused]
 
Posted by Clinton Hunt (Member # 2072) on May 02, 2017, 07:13 PM:
 
Hi Tom,
All I can say is it worked for me,the speed sounds right to me now.
I haven't tried to make it slower doing the same thing.
I'm sure someone will have the answer [Smile]
 


Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2