Posts: 2232
From: Sarpsborg, Norway
Registered: Nov 2012
posted July 27, 2013 10:43 AM
I just got a new (old really) ST-1200HD MO and it seems to run at about 20 fps or so. Much too slow and it's apparant in the sound, so I guess it's around that framerate. Is there anything I can check or adjust?
Posts: 1149
From: Washington DC
Registered: Oct 2006
posted July 27, 2013 02:50 PM
I have always made a habit of running my 1200 (no lamp) for about four to five minutes before screening anything. This gets the flywheel up to speed and stabilizes the projector for sound use.
Claus.
-------------------- "Why are there shots of deserts in a scene that's supposed to take place in Belgium during the winter?" (Review of 'Battle of the Bulge'.)
Posts: 2232
From: Sarpsborg, Norway
Registered: Nov 2012
posted July 27, 2013 03:09 PM
Asked my son to try it out, waiting for response now. So if it's the same as yours, is it fixable? My two other ST-1200's are not like this.
Posts: 7477
From: Manchester Uk
Registered: Aug 2012
posted July 27, 2013 06:41 PM
The problem with all projectors that use a ac motor for the main drive section as opposed to a dc motor, is that they rely on some kind of mechanical switching process and usually clutch arrangement to adjust from 24fps to 18fps. As a result they all have intermediate rubber wheels driving the main shaft. The rubber on steel (or rubber) as is evident in the ST 1200 series (as well as many others) has this mechanical rubber tyre arrangement via a sprung clutch to the shutter wheel and main drive shaft. The problem with this arrangement is it relies on good friction and constant spring pressure. Rubber tyres, springs and mechanical clutches all wear in time resulting in slippage and therefore a slower drive speed than intended. Unless the owner is prepared to constantly maintain all of these items to get them back to original specification, I am afraid we all have to accept the end result of many hours of use and deterioration to these parts and settle for less than perfect. Any machine using an electronically governed dc drive mechanism for the main drive on the projector ie Elmo GS1200 or Bauer T610, 510 etc etc, doesn't witness these problems as they are more or less directly driven apart from a main drive belt which generally doesn't suffer from lack of friction until it snaps apart from if lubrication comes into contact with it and associated pulleys.
-------------------- "C'mon Baggy..Get with the beat"
Posts: 4837
From: Plymouth U.K
Registered: Dec 2003
posted July 28, 2013 03:15 AM
It sounds like it may just need a good clean up in the drive system and refresh lube, has it been sat around for a while?
Posts: 2232
From: Sarpsborg, Norway
Registered: Nov 2012
posted July 28, 2013 04:13 AM
I believe it's been at a stand still for a while, yes. But it's not uneven slow, it's a constant 20 or so frames I think. I will open it next time my son comes around and see if anything is looking in need of oil
Posts: 7477
From: Manchester Uk
Registered: Aug 2012
posted July 28, 2013 06:07 AM
What could you possibly oil to make the machine go faster? I would be inclined to check for wear on the rubber wheels and that the springs are pulling the clutch to the shutter firmly in both speed settings first. These machines have a relatively powerful motor for what they are driving and unless the rotor has overheated severely or the stator windings were more or less burned out, the speed of these type of motors will be at synchronous design speed. Usually just by applying pressure to the speed controlling lever you will see a difference in the speed as more or less friction is applied to the shutter wheel from the clutch and drive chain.
-------------------- "C'mon Baggy..Get with the beat"
Posts: 2232
From: Sarpsborg, Norway
Registered: Nov 2012
posted July 28, 2013 06:32 AM
Will test that too, thanks
I am thinking things that go round and not been used for a while, often need oil. As my Chinon was doing the same, going slower and slower. Opened up the arms and oiled it, runs smooth now.
Posts: 7477
From: Manchester Uk
Registered: Aug 2012
posted July 28, 2013 10:10 AM
on these machines very little, if anything requires oiling, just use Alvania grease to lube metal rotating non friction parts and silicon grease for nylon gears.
-------------------- "C'mon Baggy..Get with the beat"
Posts: 421
From: Hillside, NJ USA
Registered: Jan 2004
posted July 28, 2013 10:51 AM
Vidar,
With the rear cover off, plug it it and turn it on. You don't need film at this point since you should still hear it running slowly. Lift the clutch/speed wheel assembly lever away from the shutter and bring it back down again. Try that several times; then try it with film (with the cover on). Keep it running and it should pick up. A worn out wheel isn't the cause of it running slowly. Loud, yes.
It's definitely not the motor. Those motors are built to last indefinitely. The only other problem could be a capacitor (which is essentially the start up device) and is simple to remove and install.
Hope this helps. Let us know.
-------------------- "the image is about 30 feet ahead of us."
Posts: 7477
From: Manchester Uk
Registered: Aug 2012
posted July 28, 2013 03:03 PM
Johns advice is spot on but also test the spring pressure and clutch assy is correctly positioned as on some of these the whole clutch pivots on a stationary piece of the structure and can sometimes become dislodged and therefore out of postion. This is a feature found on the later D's & HD's done as a mod by Elmo to try to improve the drive chain mechanism. If anyone has previously removed the clutch then it is very likely to be put back out of position and therefore not work correctly. On the original standard ST's they had a simpler version of this mechanism and often were not even fitted a spring to pull the clutch onto the shutter despite the fact that the lugs were there to fit one if needed.
-------------------- "C'mon Baggy..Get with the beat"
Posts: 421
From: Hillside, NJ USA
Registered: Jan 2004
posted July 29, 2013 08:15 PM
Andrew, yes. The spring could lose it's tension also. The other slight problem is removing the clutch assembly. It's relatively simple to remove (only two screws) but I didn't want to suggest to Vidar attempting this since putting it back is trickier. Anyone who is unfamiliar with how it goes back will have a hard time adjusting the safety shutter. If it's not re installed perfectly, the image will be dim. The safety shutter won't spring back up entirely. I've learnt how do do it after an hour of playing around with it.
-------------------- "the image is about 30 feet ahead of us."