This is topic Wanted To Buy: Regular 8mm tape splicer in forum 8mm equipment for sale/trade at 8mm Forum.
To visit this topic, use this URL:
https://8mmforum.film-tech.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=3;t=000497
Posted by Chip Gelmini (Member # 44) on September 23, 2007, 09:53 PM:
Must be in mint condition. Not interested in Kodak "presstape." Was never really good using that kind. Prefer a decent standard 8mm splicer that has pins to hold tape down before setting to film, so that sprockets align with the pre cut tapes. Accepting recommendations of kinds that I can be on the lookout to buy.
I am all set with super 8 stuff. This really must be old fashioned reg 8/standard 8mm format.
Thanks in advance.
CG
Posted by Craig Hamilton (Member # 258) on September 28, 2007, 12:40 PM:
Try this one
Splicer
Craig
Posted by Lee Mannering (Member # 728) on October 01, 2007, 05:53 AM:
Chip. If you get stuck for a Std 8 tape splicer my friend has a as new & box one for sale and is not yet listed on ebay. You can contact him through his ebay like if its of interest.
Its a very nice item and I have seen it myself.
Here is his link via ebay.
120165699965
Regards
A little update: Chip I have got the OK to forward the contact details to you direct re Std 8 tape splicer.
Best wishes.
[ October 01, 2007, 10:14 AM: Message edited by: Lee Mannering ]
Posted by Yanis Tzortzis (Member # 434) on October 02, 2007, 05:09 AM:
Chip,
if you haven't sorted it out yet, here's another one:
http://cgi.ebay.co.uk/CIR-Standard-8-cine-film-Tape-Splicer_W0QQitemZ270170976037QQihZ017QQcategoryZ4702QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Posted by Chip Gelmini (Member # 44) on October 02, 2007, 02:06 PM:
Hello
Thank you everyone. I have found what I am looking for so now I am all set.
I appreciate your replies.
Chip
Posted by Chip Gelmini (Member # 44) on October 18, 2007, 08:05 AM:
Darn it.
I paid for one splicer waiting for it to arrive. Realized my 16mm Ciro Guillotine tape splicer could make 8mm splices all this time. For those interested, the application is just a few steps different...
Peel the tape over the top side press and cut.
Lift the film off the matrix along with the double wide splice tape.
Bend over the other side with your fingers and depress.
Reposition the film to the matrix and punch out the sprockets covered by the tape on the bottom side. Repeat this step several times to make sure all sprockets under the tape are punched.
Darn it. I'll take the 8mm splicer anyway!
CG
Posted by Mike Carro (Member # 933) on November 16, 2007, 09:53 PM:
I could use a standard 8 splicer or a dual 8 (even better).
Anyone?
thanks,
will buy or trade film
pmcarro@cox.net
Posted by Craig Hamilton (Member # 258) on November 17, 2007, 01:40 AM:
Hi Mike
Welcome to the forum. Are you looking for a tape or a dual cement splicer?
Craig
Posted by Mike Carro (Member # 933) on November 17, 2007, 05:58 PM:
Hey Craig, thank you.
I'm looking for a tape splicer because I just bought some press tape but is cement better for 8mm/S8mm?
Thanks!
Posted by Craig Hamilton (Member # 258) on November 17, 2007, 06:43 PM:
Mike
Tape splices are best as cement has problems with polly film stock.
Craig
Posted by Mike Carro (Member # 933) on November 18, 2007, 09:43 AM:
I'm doing some transfers of home movies. So, they're not polyester.
Posted by Mike Carro (Member # 933) on November 19, 2007, 11:17 AM:
Anyway, I think I'm good on a splicer. I just realized I can use my 16mm guillotine.
Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC
UBB.classicTM
6.3.1.2