8mm Forum


  
my profile | my password | search | faq | register | forum home
  next oldest topic   next newest topic
» 8mm Forum   » 8mm Forum   » Elmo GS 1200: ESS mode is not working

 - UBBFriend: Email this page to someone!    
Author Topic: Elmo GS 1200: ESS mode is not working
Rene Ruppert
Junior
Posts: 22
From: Mainz, Germany
Registered: May 2016


 - posted September 06, 2019 11:41 AM      Profile for Rene Ruppert   Email Rene Ruppert   Send New Private Message       Edit/Delete Post 
After fixing the take-up arm of my “new” GS 1200 (first version) I noticed a problem with the ESS mode. I tried to run the Elmo by feeding a sync signal for the first time (usually I use my Braun Visacustic for re-recordings). I’m using a self-made cable with RCA und DIN plugs - signal on pin 4 and ground on 5, as described here:

http://8mmforum.film-tech.com/cgi-bin/ubb/ultimatebb.cgi?ubb=get_topic;f=1;t=001956;p=1

The problem is that the projector – which is set correctly to the “ESS” mode – does not react to the sync signal. Even the pulse level doesn’t show any reaction, the needle isn’t moving at all. I tried two different 24Hz square signals (generated with Audacity and Audition) and tried to play from a BD player (RCA out) and a notebook (headphone output) – without success.

Is there anything I could try to get the machine working?

 |  IP: Logged

Phil Murat
Jedi Master Film Handler

Posts: 671
From: Villeneuve St Georges, France
Registered: Dec 2015


 - posted September 06, 2019 01:13 PM      Profile for Phil Murat   Email Phil Murat   Send New Private Message       Edit/Delete Post 
Hello Rene,

From my side , I use a Synchro-Box (Home Made) which shows an adjustable "Pulse Gain" and gives a very good square signal.

You increase gain untill projector starts.

Then it is also recommended to use short shielded cables with good connectors.

Moveover, in case "ESS" sliding switch is sometime faulty , you can soak it with a powerfull contact cleaner (spray gun)

 |  IP: Logged

Rene Ruppert
Junior
Posts: 22
From: Mainz, Germany
Registered: May 2016


 - posted September 06, 2019 01:19 PM      Profile for Rene Ruppert   Email Rene Ruppert   Send New Private Message       Edit/Delete Post 
Hello Phil,
Thanks for your answer! I'll try to clean the switch tomorrow.

 |  IP: Logged

Rene Ruppert
Junior
Posts: 22
From: Mainz, Germany
Registered: May 2016


 - posted September 07, 2019 04:24 AM      Profile for Rene Ruppert   Email Rene Ruppert   Send New Private Message       Edit/Delete Post 
Today I tried again and besides cleaning the ESS switch I raised the level of the sync signal with an amplifier. The needle of the pulse level reacted at once and the projector started. I played a film for testing and the Elmo ran perfectly in sync with the digital sound. So it seems that the Elmo needs a "stronger" signal than my Visacustic.

 |  IP: Logged

Phil Murat
Jedi Master Film Handler

Posts: 671
From: Villeneuve St Georges, France
Registered: Dec 2015


 - posted September 07, 2019 11:56 AM      Profile for Phil Murat   Email Phil Murat   Send New Private Message       Edit/Delete Post 
Hi Rene,

Thanks for these informations.
A powerfull signal to run the Elmo GS1200 prevent you from unwanted mahine starts or synchro faults due to external frequencies polution (Ex : power frequencies, any radio waves, etc....)
Once more, best quality shielded cables are recommended.

 |  IP: Logged

Paul Browning
Phenomenal Film Handler

Posts: 1006
From: West Midlands United Kingdom
Registered: Aug 2011


 - posted September 07, 2019 02:13 PM      Profile for Paul Browning   Email Paul Browning   Send New Private Message       Edit/Delete Post 
Rene, there was something about the capacitor on the board drying out, generally due to not being used for a period of time. I looked for in the tech info but its not there. I have generated square wave signals like you with audacity and run it straight into the gs from the computer with no problem with the levels, so it could be this capacitor at fault.

 |  IP: Logged

Rene Ruppert
Junior
Posts: 22
From: Mainz, Germany
Registered: May 2016


 - posted September 07, 2019 02:40 PM      Profile for Rene Ruppert   Email Rene Ruppert   Send New Private Message       Edit/Delete Post 
Hi Phil and Paul,
Thanks for your support! Today I re-recorded two reels of a Derann feature and the sound was in perfect sync. The capacitor may have dried out, but as long as the "workaround" helps, it's o.k. with me.
But when I checked the recording, I noticed a high-frequent noise on both tracks which appears towards the end of the reels. When I got the projector, this noise was present during playback - pressing the recording buttons a few times helped. I read about a capacitor that's well known for making trouble during recording (when it gets hotter?). But soldering on the circuit board goes beyond my abilities ...

 |  IP: Logged

Phil Murat
Jedi Master Film Handler

Posts: 671
From: Villeneuve St Georges, France
Registered: Dec 2015


 - posted September 07, 2019 11:26 PM      Profile for Phil Murat   Email Phil Murat   Send New Private Message       Edit/Delete Post 
Hi Rene,
Due to possible High frequencies crossing them, I suggest you to replace mentionned capacitors by 2 capacitors (same voltage but half capacity) installed in "parallel assemblies" at the same place to decrease impedance.
So that Capacitors stress is significantly decreased.

 |  IP: Logged

Rene Ruppert
Junior
Posts: 22
From: Mainz, Germany
Registered: May 2016


 - posted September 08, 2019 01:56 AM      Profile for Rene Ruppert   Email Rene Ruppert   Send New Private Message       Edit/Delete Post 
Hi Phil,
I'm afraid this hobby requires either a degree in electrical engineering or a specialist workshop in the neighborhood. Unfortunately, I have neither. ;-)
Maybe I find an engineer who can do the job. I do not want to kill the machine while repairing.

 |  IP: Logged



All times are Central  
   Close Topic    Move Topic    Delete Topic    next oldest topic   next newest topic
 - Printer-friendly view of this topic
Hop To:

Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2