8mm Forum: Elf NT2 Arm Belt required.

»	8mm Forum » 16mm Forum » Elf NT2 Arm Belt required.

UBBFriend: Email this page to someone!

Author

Topic: Elf NT2 Arm Belt required.

Robert Tucker
Jedi Master Film Handler

Posts: 688
From: Essex, UK
Registered: May 2005

posted February 09, 2009 11:44 AM

I am after a replacement belt for an ELF NT2, can anyone tell me where I can get hold of one?

Many thanks,

| IP: Logged

Jean-Marc Toussaint
Film God

Posts: 2392
From: France
Registered: Oct 2004

posted February 09, 2009 12:16 PM

Marc Mc Williams's "Isellprojectorbelts" Ebay Store

--------------------
The Grindcave Cinema Website

| IP: Logged

Richard C Patchett
Master Film Handler

Posts: 424
From: Flint Mi 48506
Registered: Dec 2007

posted February 10, 2009 08:19 AM

Greetings

Which belt are you looking for. and if possible the part number
I may have this in stock.
In case Isellprojectorbelts will not ship overseas
RC

--------------------
RC’s Classic Collection
16 mm Parts & Service
Elmo, Eiki, Bell & Howell +
http://www.rcsclassic16mm.com/

| IP: Logged

John Whittle
Jedi Master Film Handler

Posts: 791
From: Northridge, CA USA
Registered: Jun 2003

posted February 10, 2009 11:06 AM

All arms that take the round urtheane belts use the same part (MS-850, MS-860, S-1, ST-, RM-, NT) The belts didn't change until the slot load projector when the flat take-up belt was introduced along with the timing belt rewind feed/arm belt.

Your best bet is to get hold of some urtheane belt material which is sold in bulk and splicing together your own belts. Buying any "exisiting" stocks can be risky as some of the stock are know to degrade on the shelf and old belts first break and then turn to goo.

By all means avoid--run away from--any rubber belts. These seem to work for a time and then under load will pinch into the pulley and jam the machine. These belts were offered by PRB and just don't work in Eiki projectors.

What I do is change the arms to the newer style from old SL machines so if you've run accross a machine with changed arms, then use the flat belts for take-up and toothed belt (which should never need to be replaced) for the feed arm.

John

| IP: Logged

Robert Tucker
Jedi Master Film Handler

Posts: 688
From: Essex, UK
Registered: May 2005

posted February 10, 2009 04:41 PM

I am only after one elf arm take up belt, i have bought one that was orange in colour thou it seems this belt has been spliced/ made together and does not work as it is a fraction to big.

So really i want to find a genuine Elf/Eiki belt as i don't won't to be let down again even thou it only cost me originally 3-4 pounds.

| IP: Logged

John Whittle
Jedi Master Film Handler

Posts: 791
From: Northridge, CA USA
Registered: Jun 2003

posted February 11, 2009 10:32 AM

What you have is a replacement made up of the stock urethane material I talked about. Someone mis-measured it would seem. If you go back to the supplier, they should be able to correct your belt.

An original Eiki belt over here, if it's still available would cost $30 to $40.

| IP: Logged

Richard C Patchett
Master Film Handler

Posts: 424
From: Flint Mi 48506
Registered: Dec 2007

posted February 11, 2009 03:09 PM

Greetings
The Arm belt part number is ST 13151
Its complete without any breaks A original Eiki belt NEW not old stock. I order these all the time from Eiki USA. Some times there out of stock. i ask them to backorder them
They come from Japan New
Your cost is $19.00 US Funds Plus mailing

--------------------
RC’s Classic Collection
16 mm Parts & Service
Elmo, Eiki, Bell & Howell +
http://www.rcsclassic16mm.com/

| IP: Logged

All times are Central

Printer-friendly view of this topic

UBB.classic^TM 6.3.1.2