8mm Forum: Elmo SC-18, motor problem?

»	8mm Forum » 8mm Forum » Elmo SC-18, motor problem?

UBBFriend: Email this page to someone!

Author

Topic: Elmo SC-18, motor problem?

Jack Crowe
Junior
Posts: 3
From: Brooklyn, NY
Registered: Apr 2013

posted April 12, 2013 03:02 PM

Hi everyone,
new here, but I've been reading thru the forum alllll day,

I work at a school, yesterday our Elmo SC-18 stopped running. It was working fine the last few weeks,
(Our Elmo ST-180E stopped working also,- its been modified for telecine, but that happened before I started here, so I'll stick to one problem at a time,)

It's used, 2-3 times a month I'd say, when school is in session anyway. Belts were replaced last year, and I know it was serviced around then too.

The light works, but no forward or reverse motion, the motor does nothing,
the belts are intact, in good shape.
The fuses all look fine, and I replaced them just to be sure.

I have a multimeter, and would like to do what I can myself, - the more money we save the more we can spend on other equipment.
Plus, I'd like to learn a few things.

I'm not quite sure where to start,.....but I did test a couple outlets here,..they all come in just under 125v, one was 120 one was 124, ...all are within that range.

The detachable power cord, Im sure isn't the original, is 10a 125v.
The back of the projector says Ac 115v 60Hz 200w, Lamp 12c 100w, AMP. output 3w. (4ohm)

With the back removed, just above the 3 pronged inlet, is a round plug/dial, ...set to 115v, this can be removed, and rotated for different voltages.

I don't see any thing. burn marks, etc on any of the boards,
and Ive tried changing the speed switch too.

Anything particular I should test with the mulitmeter?
What should I suspect first?
A service manual would be handy,

any advice would be appreciated,
thanks,
JC

| IP: Logged

Pasquale DAlessio
Film God

Posts: 3523
From: Bristol,RI, USA
Registered: May 2010

posted April 12, 2013 04:34 PM

Jack

WELCOME TO THE FORUM!!!!

|Check for voltage at the motor terminals. If you have to , start from the power inlet and trace up to the motor for voltage at differenet points. For example, the switch, motor, etc. Also, with no power cord plugged in, test for contiunuity at the switch when turned on or off.

Good luck.
PatD

| IP: Logged

Laksmi Breathwaite
Jedi Master Film Handler

Posts: 771
From: Las Vegas
Registered: Nov 2010

posted April 12, 2013 09:44 PM

Sounds like you wore out the motor.I have a SC-18 and when the motor is not working it is the fuse usually. Or the switch is worn out. I had a SC that lasted 30 years the motor and I just changed the belt and lamps.

--------------------
" Faster then a speeding bullet, more powerful then a Locomotive "."Look up in the sky it's a bird it's a plane it's SUPERMAN"

| IP: Logged

Jack Crowe
Junior
Posts: 3
From: Brooklyn, NY
Registered: Apr 2013

posted April 15, 2013 10:50 AM

Is there source known for these motors?
- I think we need one for our Elmo ST-180 E also,

| IP: Logged

Leon Norris
Jedi Master Film Handler

Posts: 958
From: Elkins Park, PA, USA
Registered: Jun 2012

posted April 15, 2013 03:08 PM

hey jack, Leon Norris I read about your problem and its not the motor can you please give me a call at 215-439-1228 i fix all elmo super8sound projectors. thank you Leon Norris [Confused]

| IP: Logged

frank arnstein
Jedi Master Film Handler

Posts: 534
From: Gold Coast. Australia
Registered: Jan 2005

posted April 19, 2013 05:01 PM

Hey Leon,

It's good to know you can fix all Elmos as we are always in need of good projector technicians here.

So if you know the answer to Jacks motor problem why don't you just tell him what it is in your post?
Does he really need to ring you to get the answer?

How will that benefit the other forum members who read this thread and might also want to know the answer?
Do you want us to all ring you one by one?
Why not save time and tell Jack what it is, so then we can all know the answer?

The purpose of this forum is to help all the members by freely sharing useful information to solve members projector problems. If you think you know the answer then why not post it here for all to see? Those that need to can still ring you.

dogtor frankarnstein

[Roll Eyes]

--------------------
At Projector Heaven the Focus is always on Detail.

____
[o:/o]<|=- dogtor@projectorheaven.com.au
//``\\
-----------------------------------------------

| IP: Logged

Leon Norris
Jedi Master Film Handler

Posts: 958
From: Elkins Park, PA, USA
Registered: Jun 2012

posted April 19, 2013 05:18 PM

hey frank im reponding to your post to let you know if someone needs something fix i tell them only if you need to know anything just email me thats the way i roll.thank you Leon Norris

| IP: Logged

All times are Central

Printer-friendly view of this topic

UBB.classic^TM 6.3.1.2