8mm Forum


  
my profile | my password | search | faq | register | forum home
  next oldest topic   next newest topic
» 8mm Forum   » 8mm Forum   » Chinon Replacement Power Cord

 - UBBFriend: Email this page to someone!    
Author Topic: Chinon Replacement Power Cord
Joe Balitzki
Jedi Master Film Handler

Posts: 529
From: Charleston, SC, USA
Registered: Aug 2005


 - posted July 09, 2016 07:35 AM      Profile for Joe Balitzki   Email Joe Balitzki   Send New Private Message       Edit/Delete Post 
I have misplaced the power cord for my Chinon 9500 projector. Until I find it I was wondering if a replacement power cord for a laptop or similar would work. However, there are so many to choose from that I don't know what to try. Does anyone have any suggestions?

--------------------
Movie Lovers Do It in the Dark

 |  IP: Logged

Steve Klare
Film Guy

Posts: 7016
From: Long Island, NY, USA
Registered: Jun 2003


 - posted July 09, 2016 08:18 AM      Profile for Steve Klare   Email Steve Klare   Send New Private Message       Edit/Delete Post 
Hi Joe,

Can you shoot a picture of the inlet and post it here?

BTW: If a computer power cord plugs in, you are good to go. That square plug with two corners shaved off is an international standard and anywhere it plugs in it really has to be correct electrically too.

-People like Underwriters Labs would get really bent out of shape if it didn't!

--------------------
All I ask is a wide screen and a projector to light her by...

 |  IP: Logged

Joe Balitzki
Jedi Master Film Handler

Posts: 529
From: Charleston, SC, USA
Registered: Aug 2005


 - posted July 09, 2016 10:07 AM      Profile for Joe Balitzki   Email Joe Balitzki   Send New Private Message       Edit/Delete Post 
On this auction there is a picture of the back of the projector showing the power cord inlet:
Chinon 9500 Auction on eBay

--------------------
Movie Lovers Do It in the Dark

 |  IP: Logged

Steve Klare
Film Guy

Posts: 7016
From: Long Island, NY, USA
Registered: Jun 2003


 - posted July 09, 2016 10:29 AM      Profile for Steve Klare   Email Steve Klare   Send New Private Message       Edit/Delete Post 
Unfortunately that's not the same plug. The one I'm thinking of (Standard IEC 301) has been the standard a long time and basically any PC you run into uses it.

It's used on a lot of more modern projectors too. My machines that use this one have been running on cords from dead PCs for years! (I basically can't ever lose the cords for these. There's always more.)

I think Janice may know this cord. None of my machines use it.

--------------------
All I ask is a wide screen and a projector to light her by...

 |  IP: Logged

Joe Balitzki
Jedi Master Film Handler

Posts: 529
From: Charleston, SC, USA
Registered: Aug 2005


 - posted July 09, 2016 10:57 AM      Profile for Joe Balitzki   Email Joe Balitzki   Send New Private Message       Edit/Delete Post 
I know the plug you are referring to; my Elmos use them.

--------------------
Movie Lovers Do It in the Dark

 |  IP: Logged

Maurice Leakey
Film God

Posts: 5895
From: Bristol. United Kingdom
Registered: Oct 2007


 - posted July 09, 2016 02:50 PM      Profile for Maurice Leakey   Email Maurice Leakey   Send New Private Message       Edit/Delete Post 
Joe
Why not rewire with an IEC connector?
http://www.ebay.com/itm/Hot-Sale-IEC-320-C14-Male-Plug-3-Pins-PCB-Panel-Power-Inlet-Socket-Connector-SG-/331340892318

http://www.ebay.com/itm/3-ft-18-AWG-Universal-Right-Angle-Power-Cord-IEC320-C13-to-NEMA-5-15P-/222094181454?hash=item33b5d8444e:g:OxoAAOSwx-9WzRkj

--------------------
Maurice

 |  IP: Logged

Steve Klare
Film Guy

Posts: 7016
From: Long Island, NY, USA
Registered: Jun 2003


 - posted July 09, 2016 03:48 PM      Profile for Steve Klare   Email Steve Klare   Send New Private Message       Edit/Delete Post 
You could do that, but you'd have to be really careful: there are several ways of wiring it wrong that would actually allow the machine to work normally, but become potentially dangerous.

For example if you switched the line and neutral connections inside, the fuse would now be on the neutral side and if there was a short to chassis, the fuse wouldn't blow and if you are very lucky all that will happen is the wiring will melt.

The other one is sometimes people don't reconnect chassis and earth ground. Now if there is a short inside the chassis is at line voltage and if you touch it, so are YOU! If you then touch something grounded, you are now electric!

(I bought a machine wired like this once...)

Then again if you flipped neutral and ground, you would pop GFI (RCD) outlets. If you flipped line and ground, you'd pop the panel circuit breaker after a huge spark when you plugged it in.

3 connections: 1 way to connect them right!

-but as long as you know what's what, you'll do fine.

--------------------
All I ask is a wide screen and a projector to light her by...

 |  IP: Logged

Joe Balitzki
Jedi Master Film Handler

Posts: 529
From: Charleston, SC, USA
Registered: Aug 2005


 - posted July 09, 2016 04:04 PM      Profile for Joe Balitzki   Email Joe Balitzki   Send New Private Message       Edit/Delete Post 
I do not have any knowledge of electrical wiring. Don't even own a voltmeter and I am no good with a soldering iron. I'm going to leave well enough alone! I may simply buy a Chinon or GAF for parts and swap out the cord. While a laptop cord may work I don't know which one to buy as there are many to choose from online.

--------------------
Movie Lovers Do It in the Dark

 |  IP: Logged

Janice Glesser
Film Goddess

Posts: 3468
From: Sunnyvale, CA USA
Registered: Sep 2011


 - posted July 09, 2016 11:02 PM      Profile for Janice Glesser     Send New Private Message       Edit/Delete Post 
Hi Joe....I have found that these 2-Prong Power Cords compatible with Kodak Slide Projectors work well in Chinons and other 2-Prong power outlet projectors. If a little tight just adjust until it fits. They aren't very long...but you can plug it into an extension cord. Very inexpensive and an easy replacement.

http://www.ebay.com/itm/AC-Power-Cor d-Cable-Outlet-Plug-Electric-Lead-For-KODAK-Carousel-Slide-Projector-/121300246233?hash=item1c3e0eded9

--------------------
Janice

"I'm having a very good day!"
Richard Dreyfuss - Let It Ride (1989).

 |  IP: Logged

Steve Klare
Film Guy

Posts: 7016
From: Long Island, NY, USA
Registered: Jun 2003


 - posted July 09, 2016 11:54 PM      Profile for Steve Klare   Email Steve Klare   Send New Private Message       Edit/Delete Post 
See!

-you don't need to know everything!

You just need to know who knows!

Janice? Is this machine plastic cased? A metal cased machine really needs that third prong.

In really olden times there were metal cased ungrounded appliances.

-then again they also used asbestos "snow" in Christmas displays!

--------------------
All I ask is a wide screen and a projector to light her by...

 |  IP: Logged

Janice Glesser
Film Goddess

Posts: 3468
From: Sunnyvale, CA USA
Registered: Sep 2011


 - posted July 10, 2016 01:09 AM      Profile for Janice Glesser     Send New Private Message       Edit/Delete Post 
Steve...Joe will have to confirm that the case on his 9500 is plastic. My guess is yes. I haven't seen a Chinon case that wasn't. I have a Chinon 7800 and oddly enough it has a 3-prong computer plug. However in addition to Chinons...the two-prong plugs are very common on several projector models made in Japan and Hong Kong...such as Sankyos (1000, 2000H, 600)...Keystone 2500... B&H 10MS, 11XJ. 20XS to name a few.

--------------------
Janice

"I'm having a very good day!"
Richard Dreyfuss - Let It Ride (1989).

 |  IP: Logged

Joe Balitzki
Jedi Master Film Handler

Posts: 529
From: Charleston, SC, USA
Registered: Aug 2005


 - posted July 10, 2016 08:52 AM      Profile for Joe Balitzki   Email Joe Balitzki   Send New Private Message       Edit/Delete Post 
Yes, the Chinon 9500 projector has a plastic case. That would explain why the plug is not 3 prong. I have ordered the power cord Janice; will let you know how it fits. I also ordered a Chinon 6100 for parts that has the power cord. One of the cords should work! While the 9500 has a plastic case, its quite heavy nonetheless. I was frustrated when I removed the 9500 from its box as everything was there except the power cord. Why I didn't put the cord in the box when I last used it I have no idea! The one thing that I wish the 9500 had is 800' reel capacity instead of 600'. This Thread is yet another example of why Janice is our resident Bond Girl! [Smile]

--------------------
Movie Lovers Do It in the Dark

 |  IP: Logged



All times are Central  
   Close Topic    Move Topic    Delete Topic    next oldest topic   next newest topic
 - Printer-friendly view of this topic
Hop To:

Visit www.film-tech.com for free equipment manual downloads. Copyright 2003-2019 Film-Tech Cinema Systems LLC

Powered by Infopop Corporation
UBB.classicTM 6.3.1.2