posted August 20, 2012 07:55 PM
I recently purchased a Eumig projector model S710D. I was told it was a top of the line machine and I bought it at a very reasonable price. It worked for a little while but all of a sudden it is projecting films at a slow pace. I checked and it is set for 24 fps. It is only a little bit slow but enough to notice. I'm sure there is an easy solution but I am quite new to this hobby and don't know the first thing about taking this machine apart without ruining it. Any help would be appreciated.
-------------------- It's 1 o'clock and time for lunch
posted August 20, 2012 10:41 PM
This is usually a pretty easy fix. Just take the back cover off (2 screws) then towards the rear of the projector you will see 2 rubber surfaced discs facing each other. These rubber discs just seem to get slippery with time and age so the drive wheel slips a little on them. Cleaning them with rubbing alcohol seems to do the trick. I usually just take a q tip and dip it in rubbing alcohol and then hold it against the disc while it's running. Hopefully this is helpful (I'm pretty sure the insides are close to the same as some of the 800 series, which is what I have).
-------------------- There is a fine line between a hobby and a mental illness
posted August 20, 2012 11:57 PM
Zechariah, I assume you mean the two discs towards the right of the machine? Those are the only ones that have rubber on them. Do I clean one of them or both?
-------------------- It's 1 o'clock and time for lunch
Posts: 3063
From: Gt. Clifton,Cumbria,England
Registered: Jan 2012
posted August 21, 2012 07:02 AM
Exactly right Dino, this can be done while the machine is running, I have found that if the abrasive paper is fastened to a thin piece of wood,there is less chance of a new hairstyle!
Posts: 979
From: Manassas, VA. USA
Registered: Jun 2003
posted August 27, 2012 12:56 PM
I have also gone to the car parts place and gotten a spray can of "belt dressing"....and put it on the rubber wheel. it helped for while...as did sandpaper, but finally that old Mark S standard 8 sound machine just couldn't run anymore...unless the speed change switch was NOT on 24fps...which was of course where 98% of the films I had needed to be run.
posted August 30, 2012 10:12 PM
The misconception with Eumig machines is when they slow down, sanding the rubber discs is the solution. It's not. You're removing the rubber each time you sand it; even with a light paper 200 grit or what have you. If it slows down again after 6 hours of use, re sanding will further remove the rubber, then the idler in between will have nothing to rub against. After 60 hours of use, you'll have hardly any rubber remaining if sanding continues. The problem are not the rubber wheels but a spring that has too much tension and that spring takes hours to get to.
-------------------- "the image is about 30 feet ahead of us."
Posts: 654
From: Bothell, WA, USA
Registered: Mar 2010
posted August 31, 2012 01:31 AM
I don't have a Eumig projector but one of my old turntables runs with a rubber wheel in contact with the metal on the inside of the record table. When it starts to slip I clean the rubber with a rubber conditioner and the metal on the table with rubbing alcohol. The rubber conditioner is the type they sell for printers and copiers. One cleaning lasts quite a while. It's a 50 year old turn table and I assume the rubber is that old as well.
David Kilderry
Jedi Master Film Handler Posts: 963
From: Melbourne, Victoria, Australia
Registered: Feb 2006
posted August 31, 2012 01:52 AM
I overcame my Eumig 940 speed problems ( alcohol, and the slightest roughing of the surfaces), but alas the sound heads have worn where now it won't reproduce the balance track and it is not as clear on the main track. This is the problem that will bury these fine projectors as they age.
Anyone have any sound head replacement options for the stereo Eumigs?
Posts: 977
From: Ortona, Italy
Registered: Jan 2004
posted August 31, 2012 09:43 AM
If it's not too late, you should be able to have your sound head reprofiled (it's been discussed in the forum in the past).
As for sanding the rubber discs: once they've been rubbed, they shoud last at least for some years without need of further sanding. True it is you are "destroying" their surfaces but it is really superficial, I mean on the extreme outer surface and this won't affect speed. INdeed such operation only takes away the hardened outer surface of the discs (rubber tends to harden over the years); nothing more. ANd it will last as it did (and dors) on my Eumigs. If the projector slows down again after sanding the discs, then there must be another problem, possibly one of hardened old grease (lubricant): this puts much more strain on the motor and the whole mechanics and eventually mau make sanding the discs useless. In this case you have to remove the old lubricant and re-grease all the rilevant moving parts; only then you can sand the discs.
I undertstand after 4-5 sandings, the discs will be useless, but this will have granted themachine at least some more 10 years of working life. Then changing the discs altogether is certianly an option to consider.
Posts: 3063
From: Gt. Clifton,Cumbria,England
Registered: Jan 2012
posted December 20, 2012 05:42 AM
Hi David I did put up a couple of addresses on the forum regarding reprofiling of soundheads for EUMIG projectors,one of the proprietors of the company told me that soundheads can still be obtained for EUMIGS.Both firms are in the UK.
Posts: 372
From: Montrose, NY
Registered: Feb 2011
posted December 20, 2012 10:38 AM
John Capazzo is correct. Sanding is a quick fix and not the solution. The spring tension is the problem. It's hard to fix on the 710. Easier to fix on the 800 models, (easy access).....The ball needs more pressure to the rubber discs. A well used eumig with grooves formed in the rubber will be another major problem...
posted December 20, 2012 11:22 AM
Something like this, Vincent? I got an S938 on ebay, and I noticed it slowing down and rattling, once the take up reel gets fuller. There's a thread with more pictures here: . 8mm Forum
When you said "grooves", I suppose you mean the "rings" on what I called "big wheels". What can be done about that? Haven't done anything with them wheels yet... Thanks a lot...
-------------------- Vinegar belongs in the salad...
Posts: 372
From: Montrose, NY
Registered: Feb 2011
posted December 20, 2012 02:21 PM
Not much can be done other than replacement. years of the metal ball riding on the same spot makes for poor contact. Wish it was as simple as replacing a belt. Keep an eye out for a broken projector at a low price. Try to find one that was owned by someone who only watched home movies on it. It's more likely that it doesn't have many miles on it....