8mm Forum: Just Replaced Micro Switch in DCT

»	8mm Forum » 8mm Forum » Just Replaced Micro Switch in DCT

UBBFriend: Email this page to someone!

Author

Topic: Just Replaced Micro Switch in DCT

Steve Carter
Master Film Handler

Posts: 282
From: Bristol, UK
Registered: Apr 2015

posted May 05, 2015 05:40 PM

At last the parts have come, I bought two micro switches from China only cost 99p how do they do it.I was very apprehensive about the repair, I am no stranger to the soldering iron, but due to an illness I suffer with uncontrollable tremors, any-ways I managed to de-solder the old switch, and with some small clamps and forceps, fitted the new switch, and with the new brushes which I made from over-size one's, the old DCT runs as smooth as when it was first out of the box. I'm feeling good about doing this, it's a bit of an achievement.

| IP: Logged

Barry Fritz
Phenomenal Film Handler

Posts: 1061
From: Burnsville, MN, USA
Registered: Dec 2009

posted May 05, 2015 05:52 PM

How do the Chinese do it? By using the cheapest materials possible and by paying their workers next to nothing.

| IP: Logged

Janice Glesser
Film Goddess

Posts: 3468
From: Sunnyvale, CA USA
Registered: Sep 2011

posted May 05, 2015 10:53 PM

It IS a big accomplishment Steve....nice work. You should be proud [Smile]

--------------------
Janice

"I'm having a very good day!"
Richard Dreyfuss - Let It Ride (1989).

| IP: Logged

Steve Carter
Master Film Handler

Posts: 282
From: Bristol, UK
Registered: Apr 2015

posted May 06, 2015 04:08 AM

Thank-you Janice,you reply is very much appreciated.
If I purchase the switches here in the UK, the chances are they are the same Chinese one's, at a big price mark up, so why not buy at source?,the factory fitted ones in the DCT are known to be the main fault with motor failing, so they are not that well made....

| IP: Logged

Bill Parsons
Film Handler

Posts: 66
From: Brookland. UK
Registered: Jul 2004

posted May 06, 2015 10:56 AM

Well done Steve, replacing those switches is a bit of a fiddly job for those of us working on projectors all the time; I can understand it gives a feeling of satisfaction.

| IP: Logged

Janice Glesser
Film Goddess

Posts: 3468
From: Sunnyvale, CA USA
Registered: Sep 2011

posted May 06, 2015 11:03 AM

I'm thinking the micro switches on my Sankyo 600 might be the source of its intermittent power loss problem. If that's the case then I'm not sure I want to tackle replacing them right now. [Eek!]

--------------------
Janice

"I'm having a very good day!"
Richard Dreyfuss - Let It Ride (1989).

| IP: Logged

Steve Carter
Master Film Handler

Posts: 282
From: Bristol, UK
Registered: Apr 2015

posted May 06, 2015 12:23 PM

Yes Janice I had intermittent forward power loss, after testing and cleaning all contacts etc, I found it to be one of the micro switches, I believe the Sankyo is much the same as the Bell & Howell DCT.,it's a pig of a job as the track selector rods cover one of the screw bolts which hold the micro in place, but I am always willing to give my advice after completing this replacement...I believe in sharing knowledge gained...

| IP: Logged

Janice Glesser
Film Goddess

Posts: 3468
From: Sunnyvale, CA USA
Registered: Sep 2011

posted May 07, 2015 02:21 PM

Steve, I will definitely be asking for your assistance in the future. Sounds like you have hit on the resolution to the problem with one of my Sankyos. Those micro switches are buried pretty deeply and not easy to get to. However I think it's well worth the effort to repair what otherwise is a great running projector.

[ May 07, 2015, 04:44 PM: Message edited by: Janice Glesser ]

--------------------
Janice

"I'm having a very good day!"
Richard Dreyfuss - Let It Ride (1989).

| IP: Logged

Andrew Woodcock
Film God

Posts: 7477
From: Manchester Uk
Registered: Aug 2012

posted May 07, 2015 02:30 PM

Well done indeed Steve! [Smile]

--------------------
"C'mon Baggy..Get with the beat"

| IP: Logged

All times are Central

Printer-friendly view of this topic

UBB.classic^TM 6.3.1.2