Welcome to the new 8mm Forum!
The forum you are looking at is entirely new software. Because there was no good way to import all of the old archived data from the last 20 years on the old software, everyone will need to register for a new account to participate.
To access the original forums from 2003-2019 which are now a "read only" status, click on the "FORUM ARCHIVE" link above.
Please remember registering with your first and last REAL name is mandatory. This forum is for professionals and fake names are not permitted. To get to the registration page click here.
Once the registration has been approved, you will be able to login via the link in the upper right corner of this page.
Also, please remember while it is highly encouraged to upload an avatar image to your profile, is not a requirement. If you choose to upload an avatar image, please remember that it IS a requirement that the image must be a clear photo of your face.
Thank you!
The projector (like most of my collection) is 125v but I always have a transformer at hand.
The funny thing is that when I plugged it in, smoke started coming out of the transformer, so I guess it has an internal electrical problem.
If smoke was coming out of your 220 to 110 volt step down transformer it probably now has shorted windings inside and is probably ruined. I recommend you no longer use that transformer!
Those older projectors draw a lot more current than the newer ones. It could be that your transformer could not handle it (hence the smoke) and the projector might be fine. The bulb alone could use up 5 to 6 Amps at 120V and maybe another two for the motor. . What is (or was) the output rating on your transformer?
The transformer has a capacity of up to 750W. I have already connected 500W projectors to it without any problem. The projector has a power failure
That's kind of borderline. IIRC, those bulbs can be 500W or 750W (4.8A to 6.25A).For an older motoer like that, allow another 2A (240 Watts) and you at 740W at the low end and close to a KW at the high end.
Not saying the projector is definitely good, just that there is a possibility it is not as bad as you think. Super easy way to test is just without the bulb (well under 750W that way) and see if it runs. They are incredibly basic electrically so unless something is shorting or the motor seized up , there is not to go wrong in that respect. You maay have done that already and if so, my apologies.
I thinkk the knob on the front is also directly connected to the motor. If you can turn it, the motor is not seized. ETA - Actually, my mistake I think the knob is NOT directly connected, but connectied via a belt.
Of course, you could be absolutely correct in that the projector has an issue, but if it was MY projector, I would be want to verify the issue was the projector before I thught about sending it off.
Last edited by Alister Hibbert; December 02, 2022, 10:28 AM.
What you are talking about is very difficult for me, how do I know the amps?
Amps is basically Watts divided by Voltage. Things like motors and lamps draw ('pull') current (measured in amps). Household circuit capacity is measured in amps.
Lamps are typically marked in watts so its easy to calculate how much current they draw. Motors are harder to determine without a multimeter (unless they are marked with a plate telling you), so I am making a guess at how much to allow for it.
The point is that the motor and lamp will try to pull x amount of amps total. If that total is more than 6.25A, it will exceed the capacity of the transformer. If the bulb is a 750W bulb, then it does not matter what the motor is rated at as you have already maxed out the transformer.
One last note, even if you have a multimeter, don't try to test it. You have to make the multimeter part of the circuit to measure current and that can dangerous with household levels of current, so you really need to know what you are doing to avoid getting zapped or blowing up the meter.
So, in my case it would be 2.4 amps, right?
125V and lamp 300W
Correct, that would leave you a little under 4A available for the motor. That should be more than enough. I just tested my Keystone K109, which is a similar style of projector and the with the motor only om it draws a little over 1A (so allowing for 2A is plenty).
With the lamp on, mine is drawing 7.3A as my bulb is much higher wattage
So if your bulb is only 300W, it should be under the 750W limit for the transformer.
I would still try turning the motor by hand and if is not seized, try the projector briefly without a bulb.
Yea, the motor issue still has not been resolved. Has the motor ever run at all on this projector, regardless of the lamp issue? You have never once mentioned the motor running or not, even before the the step down transformer smoked.
Could it be possible that someone connected the projector to the 220 volt mains without a step down transformer in the past?
I also have a Keystone K109 which works perfectly at 125V. I just got the EMEL and haven't tried it before so I guess it was already broken. The motor rotation does not appear to be faulty. I have it at an electrical service to have it checked as I have not received the contract from the Barcelona service.
Tweet
Comment